How To Polish Your Car Paint Easily and Quickly - Spray Painting
It isn't the tools that are used in a job that make it good or bad, it's the person using those tools that makes the difference. In car polishing a good technician can make that finish look better than when you bought the car, and you wouldn't think twice about how they could do that. In this short article, I will go over some points that technicians know, or should know.
The main problems when it comes to auto finishing are things like paint runs, sags, dirt nibs and just plain old polishing in general. To start with, make sure that the finish is dry in accordance with the information from the product sheet as failure to do this could damage the finish, making the whole job very costly.
The proper way to polish when using a polish, make sure it is specifically or can be used for urethane finishes and not lacquer finishes. When sanding, make sure that you use the finer 1000grit paper, as course grit sandpaper can ruin a finish.
The polisher speed should be set at 1200 ? 1700 rpm?s to ensure the best result. It is also very important to make sure that you are using the right type of pad before you start. To know what the best pad types, always check the product data sheets and they?ll steer you in the right direction, remember, if in doubt, check the sheet.
On the blend edges when you are, polishing be sure to work away from the edge and never directly into it. The most recommended method for a blend edge is to hand glaze rather than machine polish. When you have to hand glaze, always a cloth that is not rough and make sure it is clean forboth the application and when taking the glaze off.
Getting Rid Of Imperfections As with polishing, always check with the right manufacturers product data sheet before sanding, or polishing, this will give you the recommended dry times before polishing. Always make sure that before you begin any work on the surface that you take off debris and material. If this isn?t done, the results will be costly and catastrophic.
It is so important that the proper prep work be done so that the surface is: Free of imperfections like dirt nibs. You can use 1500 or better grit for wet sanding to get rid of these. To make sure there are no more imperfections on the surface, sand the surface with a block sander, not necessarily the entire surface, spot sanding will do.
The Last Step Use the polisher lightly to eliminate sand scratches using the right liquid polish. When using the polisher, set it to 1200 ? 1700 rpm and use a wool pad first. Next, you will need to use a foam pad. Finally, you need a non- abrasive glaze. Always remember that if you are in doubt about what to use or how to do it, consult the manufacturer?s list of instruction and information data sheet .Don?t be in a hurry, if you take your time you won?t make the mistakes that you will only regret. - 21392
The main problems when it comes to auto finishing are things like paint runs, sags, dirt nibs and just plain old polishing in general. To start with, make sure that the finish is dry in accordance with the information from the product sheet as failure to do this could damage the finish, making the whole job very costly.
The proper way to polish when using a polish, make sure it is specifically or can be used for urethane finishes and not lacquer finishes. When sanding, make sure that you use the finer 1000grit paper, as course grit sandpaper can ruin a finish.
The polisher speed should be set at 1200 ? 1700 rpm?s to ensure the best result. It is also very important to make sure that you are using the right type of pad before you start. To know what the best pad types, always check the product data sheets and they?ll steer you in the right direction, remember, if in doubt, check the sheet.
On the blend edges when you are, polishing be sure to work away from the edge and never directly into it. The most recommended method for a blend edge is to hand glaze rather than machine polish. When you have to hand glaze, always a cloth that is not rough and make sure it is clean forboth the application and when taking the glaze off.
Getting Rid Of Imperfections As with polishing, always check with the right manufacturers product data sheet before sanding, or polishing, this will give you the recommended dry times before polishing. Always make sure that before you begin any work on the surface that you take off debris and material. If this isn?t done, the results will be costly and catastrophic.
It is so important that the proper prep work be done so that the surface is: Free of imperfections like dirt nibs. You can use 1500 or better grit for wet sanding to get rid of these. To make sure there are no more imperfections on the surface, sand the surface with a block sander, not necessarily the entire surface, spot sanding will do.
The Last Step Use the polisher lightly to eliminate sand scratches using the right liquid polish. When using the polisher, set it to 1200 ? 1700 rpm and use a wool pad first. Next, you will need to use a foam pad. Finally, you need a non- abrasive glaze. Always remember that if you are in doubt about what to use or how to do it, consult the manufacturer?s list of instruction and information data sheet .Don?t be in a hurry, if you take your time you won?t make the mistakes that you will only regret. - 21392
About the Author:
Discover the easy way to learn how to spray paint on car with SprayPaintSecrets. You will learn all the tricks of the trade and techniques of car spray painting. Download your free videos at the official site now... - paint car spray paint.
posted by X - Men @ 3:41 AM
0 Comments
0 Comments:
Post a Comment
Subscribe to Post Comments [Atom]
<< Home