How Simple To Remove A Factory Car Audio
Car stereo is an integrated part of a car. Factories stereo have electrical wiring connectors that has all the wires housed in it.this set of wires include ground wire, wire for the speakers, memory and main power switch. An adaptive harness is to be purchased along with a after market radio. This will be far time consuming and also more power. This is a much simpler one compared to others. They are less expensive and they also have single switch system which is more advantageous than others. Its a simple plug in and playing type of stereo system.but how to remove a factory car stereo.
This discussion will be helpful for those aspiring to remove the factory car stereo easily without spending too much money and time. For this purpose some tools like screwdriver, quarter inch sockets, and quarter inch socket driver are required. Some steps to remove the factory car stereo are discussed below. They are a set of generalised directions which may be applicable to the car in picture since all cars are different but this definitely gives the reader an idea of how to get the car stereo removed.
Your system's entire sound can be enhanced by replacing the stock stereo of your car. This is said to be one of the best method to bring in an improvement in the sound quality of your car stereo system. In spite of giving a higher power output the new stereo system also brings a better ment in both the clarity and quality of sound in your car.
Remove any screw from the top front part of the car either the speedometer and in the dash cover remove it along the bottom line of it. The panel on the driver's side under it can be removed. The dash cover which is concealed under the panel has screws. The screws beneath the steering is removed so as to remove the panel above it.
Using a common screw driver remove the cover out. To keep the dash covers on there are snaps that snap into a hole. But if the fuses are on the drivers side then look for the screw which may be inside the cover. The dash cover will be held by these screws. the dash covers are held just by the snaps and screws.
The screws which hold the radio and which is around the face plate is pulled in. and the radio is pulled out so as to remove the electric connector and antenna. The face plate is opened and the right one for your car can be chosen. One should ensure its perfect fitting in the car with the space given.
In order to disconnect the power, the power plug to the stereo has to be located. The plug will generally have two colored wires namely red and yellow wire running to it. Using one hand, grasp one side of the plug while grasping the other side of the plug with your other hand. Once grasping the plug, squeeze them and pull them at the same time.
Hence by following the above directions, removing a factory car stereo becomes easy and can be done by any person with enough knowledge of dash covers and connections of stereos. - 21392
This discussion will be helpful for those aspiring to remove the factory car stereo easily without spending too much money and time. For this purpose some tools like screwdriver, quarter inch sockets, and quarter inch socket driver are required. Some steps to remove the factory car stereo are discussed below. They are a set of generalised directions which may be applicable to the car in picture since all cars are different but this definitely gives the reader an idea of how to get the car stereo removed.
Your system's entire sound can be enhanced by replacing the stock stereo of your car. This is said to be one of the best method to bring in an improvement in the sound quality of your car stereo system. In spite of giving a higher power output the new stereo system also brings a better ment in both the clarity and quality of sound in your car.
Remove any screw from the top front part of the car either the speedometer and in the dash cover remove it along the bottom line of it. The panel on the driver's side under it can be removed. The dash cover which is concealed under the panel has screws. The screws beneath the steering is removed so as to remove the panel above it.
Using a common screw driver remove the cover out. To keep the dash covers on there are snaps that snap into a hole. But if the fuses are on the drivers side then look for the screw which may be inside the cover. The dash cover will be held by these screws. the dash covers are held just by the snaps and screws.
The screws which hold the radio and which is around the face plate is pulled in. and the radio is pulled out so as to remove the electric connector and antenna. The face plate is opened and the right one for your car can be chosen. One should ensure its perfect fitting in the car with the space given.
In order to disconnect the power, the power plug to the stereo has to be located. The plug will generally have two colored wires namely red and yellow wire running to it. Using one hand, grasp one side of the plug while grasping the other side of the plug with your other hand. Once grasping the plug, squeeze them and pull them at the same time.
Hence by following the above directions, removing a factory car stereo becomes easy and can be done by any person with enough knowledge of dash covers and connections of stereos. - 21392
posted by X - Men @ 2:48 AM
0 Comments
0 Comments:
Post a Comment
Subscribe to Post Comments [Atom]
<< Home