Check Your Vehicle's Tire Pressures With A Digital Tire Pressure Gauge
Tire pressure gauges are a necessary tool of measure used in the safe operation of your car. These essential tools indicate to the user how much air pressure is in the tire. The air pressure in the tire is of the utmost importance because any under fill or overage of air, inside the rubber, can result in a car accident.
Inefficient air pressure, or too much in a vehicle's tire, can hurt you badly. When air is low, the vehicle can pull to the side having more pressure. On the other side of the coin, overfilling the air can result in a drag of the car's steering to the side with less air. With this as the case, it is essential to check to see the tire is filled to its specified PSI (pressure per square inch), but the same for each four tires. Therefore, if you are filling them 5 PSI, then repeat for each of the four tires.
Not only is it hazardous to have too little pressure or a lot of pressure, it is also very dangerous to put air in your tires if you do not know what you are doing. When checking the pressure of a tire, you should do the following:
1. Find the manufacturer's specification for the PSI you must inflate the tires to. This listing is typically written on the side wall of the tire. Some believe it is ok to inflate the tires a maximum of5 PSI under the manufacturer's specification. But, it is not suggested to pump them any more than what is listed. The typical automobile's tires these days take around 35 PSI. But, you should always check to make sure.
2. Aim your face away from the tire while fitting the gauge to the air stem on the tire. Hold the tire end to the stem of the tire. Steady it and center it until you do not hear any air escaping. Look at the gauge and check the reading.
3. If there is no reading, then it might indicate that you are riding on very low tires. If this is the case, inflate to the maximum PSI.
4. Measure the pressure after the fill with the gauge. It should read some level of PSI once inflated passed about 10 PSI.
5. Following this, fill and stop when reaching the maximum PSI required for the tire. Again, it is dangerous to inflate above the maximum listed PSI as designated by the tire manufacturer.
Failing to follow the above steps when measuring the pressure with a gauge can be very harmful. If a tire is overinflated, it can pop, sending chunks of the metal belt directly into your face. Most tires today are fabricated with steel layering to tighten the rubber together. This steel can become a lethal weapon that can lead to serious injury. Some have actually died from over inflating automobile tires.You can seriously reduce the risk injury by remembering to be safe. - 21392
Inefficient air pressure, or too much in a vehicle's tire, can hurt you badly. When air is low, the vehicle can pull to the side having more pressure. On the other side of the coin, overfilling the air can result in a drag of the car's steering to the side with less air. With this as the case, it is essential to check to see the tire is filled to its specified PSI (pressure per square inch), but the same for each four tires. Therefore, if you are filling them 5 PSI, then repeat for each of the four tires.
Not only is it hazardous to have too little pressure or a lot of pressure, it is also very dangerous to put air in your tires if you do not know what you are doing. When checking the pressure of a tire, you should do the following:
1. Find the manufacturer's specification for the PSI you must inflate the tires to. This listing is typically written on the side wall of the tire. Some believe it is ok to inflate the tires a maximum of5 PSI under the manufacturer's specification. But, it is not suggested to pump them any more than what is listed. The typical automobile's tires these days take around 35 PSI. But, you should always check to make sure.
2. Aim your face away from the tire while fitting the gauge to the air stem on the tire. Hold the tire end to the stem of the tire. Steady it and center it until you do not hear any air escaping. Look at the gauge and check the reading.
3. If there is no reading, then it might indicate that you are riding on very low tires. If this is the case, inflate to the maximum PSI.
4. Measure the pressure after the fill with the gauge. It should read some level of PSI once inflated passed about 10 PSI.
5. Following this, fill and stop when reaching the maximum PSI required for the tire. Again, it is dangerous to inflate above the maximum listed PSI as designated by the tire manufacturer.
Failing to follow the above steps when measuring the pressure with a gauge can be very harmful. If a tire is overinflated, it can pop, sending chunks of the metal belt directly into your face. Most tires today are fabricated with steel layering to tighten the rubber together. This steel can become a lethal weapon that can lead to serious injury. Some have actually died from over inflating automobile tires.You can seriously reduce the risk injury by remembering to be safe. - 21392
About the Author:
Xavier is a journalist with more than fifteen years editorial experience. Xavier is presently working as a reporter for the fuzing.com portal and has become the resident expert on automotive safety. Visit our useful website for more information on Tire Gauges and Pressure Gauge.
posted by X - Men @ 2:13 AM
0 Comments
0 Comments:
Post a Comment
Subscribe to Post Comments [Atom]
<< Home