Can Speed Trap Detectors Really Help You Avoid Speeding Tickets?

By Armand du Piessis

There is nothing worse than driving on a vacation in an unknown area where you may not necessarily know the speed limit and you find yourself caught in a speed trap.

A speed trap can be the cop that hides just over the crest of a hill or is hidden behind a sign where you don't really notice them. In our technological world a speed trap can also be fixed cameras that find traffic infringements and ticket people.

So wouldn't a speed trap detector be beneficial to helping you get less tickets?

In many occasions the answer is yes. Today speed trap detectors are usually gps units like the TomTom, Garmin, or even cellular phones with GPS enabled. You're able to individually indicate places on the map of places that there are commonly speeding traps. After you have this information on your gps or phone, you are be prepared for the trap waiting for you just around the bend.

A few things to consider about this technology. On the one hand some might find themselves in an area with lots of speed traps and decide to drive with added caution but at the same time someone alone keeping their focus off the road and on their phone can intensify the danger. Also a few areas throughout the country are trying to disallow the use of these features on phones such as a well-liked iPhone application that does this.

Furthermore, lots of these maps are expected to start having annual costs added to them. It could be valuable to register since it can save a little money, but it would probably be simpler to learn how to avoid speeding tickets in the first place.

Here's some terrific info for you! - 21392

About the Author:

Want to find out more about GPS Speed Camera Detector, then visit Armand du Piessis's site on how to choose the best GPS Speed Camera Detectors for your needs.

How Is Car CD Troubleshooting Done

By Rob King

Everyone enjoys listening to music while on drive. When CD player stops doing its job we take it to a repair shop. But before doing that we can try out few simple ways of car CD troubleshooting which may save us from paying huge amount for repair.

The first thing that should be done in trouble shooting is to find out the specific problem. One of the easy things that could help finding the defect is by checking whether the radio works properly or you can check the output volume of all speakers and check whether they are all equal. Once the specific defect is identified, the solution can be easily reached.

First our aim is to find out which area of the audio system causes the problem. It can be speaker, radio or the CD playback. This step is done so as to save time and this will help in finding quick solutions to fix the problem. It includes checking fade controls. This is done mainly when one speaker works but the other one does not.

The reason for not receiving the sound in the speaker may be due to break in flow of current through it. Buy a radio shack from any electronics shop and use it to check the current flow through the wires for speakers. The speaker's grill covers are unscrewed and snapped off. And then the mounted speakers are also removed.

Another possibility might be due to the damaged connections. To check this, the wires can be connected to electric meter which is available in shops. This electric meter gives a reading if there is power supply. Therefore if the wires are not connected properly or have disconnected somewhere it will show no reading. The wires can be obtained but removing the player after unscrewing the speakers.

The last thing that needs to be checked is the harness of the wiring under the dash board . Use flash light to do this. If everything is fine, the positive cable is disconnected from the battery of the car and leave it like that for a minimum of ten minutes. This time gap is given for the player to come back to the conditions in which it was preset in the factory.

There also appears a problem of disc error. In this case clean the disc drive using a lens cleaning solution. A drop of rubbing alcohol can be used for effecting the cleaning power.

Above steps can be followed to find the trouble in the CD player. But to prevent further problem it is essential to clean the CD before use with the help of soft cloth and a solvent. These are few steps of car CD troubleshooting. - 21392

About the Author:

Learn more about Autozubehoer. Stop by Author Name's site where you can find out all about Car stereo and what it can do for you.

How To Hide A Stereo Wiring In A Vehicle

By Nell Harrison

Wiring is the last thing which comes to one's mind who thinks of a new stylish, cool car stereo. It is very essential to hide the wiring for reducing the sound, and to increase performance and aesthetics. All these wires must be well insulated so as to reduce the noise levels. These noises should not be transferred to other wires or cables. A professional and custom look can be given to the car stereo if all these wiring are hidden under the insulation. This also ensures safety of the wires by avoiding contact with the passenger in the car while any kind of accidents. This will also increase the life of the wiring. But how to hide wiring in auto stereo installation?

In the cases of uncovered wires there are possibilities of the noise transfer from one cable to the others. These wires are to be hidden to give a highly professional and customized look to your car stereo. Hiding the wire will also make it live longer as it reduces risk during accidents. There are few basic tools required for this task. They are Velcro stripping material, putty knife, cable ties, cordless drill, wire cutter, sheet metal screws, hex bits, flexible cable tubing.

The first thing to be done is to conceal the main wire that is connected to the battery of the car using tubing for the cables. This can be done with the help of screws and clamps. It can be attached to the car's frame. For the screws of the clamp, holes can be drilled using the drilling machine.

In the next step for closing the tubing zip ties are attached and they are placed every two to three feet from the cable tubing. In order to avoid splicing of the wires the available harness wiring are installed. This also helps in keeping the wires together. It makes the job look cleaner and also reduces the chances of any connection fault in the wiring.

The wires of the stereo can be hidden by putting it under the plastic trim that is present along the door and under the carpet. This can be done by using a knife to pull it out. Some consultation may be done regarding the bundling of the wires so that the noise can be reduced or even avoided completely. The cable tubing can then be attached but care should be taken that screws are not fixed over the wire. The Velcro material can be used in the places where holes cannot be drilled as in the frame of the car.

The wires to the speakers at the rear, sub-woofers, amplifiers and the crossovers can be hidden behind the side of the car and panels. Instructions should be followed to remove it with no damage.

The connectors that are at the sub-woofers and the amplifiers may be seen generally. These can be inserted into the carpet or panels. For some cars there are panels that are built to reduce the wiring.

Answering the question how to hide the wiring in auto stereo installation, becomes simple by just following the steps mentioned above which will make it very simple. - 21392

About the Author:

Want to find out more about Car Hifi, then visit Author Name's site on how to choose the best Car Audio for your needs.

Connecting A Battery Isolator

By Rob King

The following article shows how to connect a battery isolator. The isolator is installed when the car needs a second battery. This will be required by cars that have bigger stereos. Since more power is needed second battery is added with the help of an isolator.

Battery isolator is a device that instructs the alternator to charge the secondary battery and also protect the primary battery from being drained. Battery isolator can be of different type but the most efficient and cheapest of them is solenoid type isolator where the isolator connection is achieved when the engine is on, off when the engine is off .The instructions on how to connect a battery isolator follows.

Open the front hood and place the secondary battery in its corresponding tray using a 3/8 inch socket and ratchet. Make sure the battery is properly in position and should not be kept tilted. Using a driller mount the battery isolator then connect the terminal of battery isolator to the positive terminal of the battery using a battery cable. The wire connecting the battery and isolator are stripped and held in position using the 3/8 inch ratchet and socket.

In the next step with the help of drill the battery isolator is mounted to the fender. For more secure connection use the brackets and self tapping screws that comes along with the battery isolator. A 4 gauge battery cable is used to connect the two batteries. It joins the positive terminal of the battery to the right side of the battery isolator. In the same way we have to connect a wire from the positive terminal of the first battery to the battery isolator. This is done using a 3/8 ratchet and socket.

The wire strippers are used to strip inch off the other end of the 18 gauge wire. A ring terminal is crimped on to the end of the wire using the wire crimpers. the wire is connected to the ignition terminal on the battery isolator using a 3/8 inch ratchet and socket.

A 18 gauge wire run from the ground terminal on the battery isolator to the ground source on the frame. a wire is bolted to the frame on the passenger side. A ring terminal is crimped on both sides of the wire using wire crimpers and it is bolted to the ground point and the battery isolator using a 3/8 inch ratchet and socket.

The negative terminal of the secondary battery is connected to the ground point on the frame using a gauge wire and is bolted on the either end to ensure connections, now the secondary battery will start charging only when the engine is on.

It is easy to couple the secondary battery with the primary battery using this manual on HOW TO CONNECT A BATTERY ISOLATOR where it eliminates the need for supervision. - 21392

About the Author:

Learn more about Autozubehoer. Visit the popular site of powernetshop.at where you can find out all about Car stereo and what it can do for you.

Steps To Install A CD Player Easily

By Sally Thompson

Those days only a cassette player was available in a car. But these days music has taken the predominant form in CD and DVD. If you still own a cassette player in any car you can easily switch over to a CD player and modernize your car yourself. This can be done at a low cost as an after market CD player can be installed. But how to install a CD player?

Here is the list of the things that you will need for completing the switch over; wire strippers, car stereo wiring connectors, 20 vinyl butt splices that are insulated awg 16-14, needle nose or combination pliers and 1 CD player dash install kit.

First locate for the wire running from the CD player, using a stripper strip the wire to half an inch, The same procedure is to be repeated for all the wires provided with wire connector, make sure only the insulation part is removed without damaging the core portion of the wire.

Insert an end of the orange wire coming out of the wiring connector of the car stereo into the vinyl insulated butt splicer. Now close this side of the splicer. This can be easily done using the nose pliers. Make sure that the butt splicer holds the wire firmly. Now insert the end of the orange wire that is coming out of the rear end of the CD player into the other end of the butt splicer and close this end with the use of the nose pliers. Be sure that there are no loose connections and the wire is held firmly by the butt splicer. Repeat this step for all the wires that can be seen in wire connecting the stereo. Make sure that each wire is matched very well with the similar colour and size of the player.

In the next step in the process we should remove the insulation from all the wires that comes from the wiring connector for car stereo. The insulation should be removed for about 1/8 to quarter inches and here also care should be taken so as to avoid the damage caused to the internal wiring.

Now one of vinyl butt splice which is insulated and the orange wire's end is inserted from the wiring connector. The connection is done securely using the pliers. The pliers are used to cover the side of vinyl insulated butt splice. Now in a similar way fix another vinyl insulated butt splice from one of the orange wires that comes out from the player. Then using the pliers the vinyl insulated butt splice is securely connected to the wire.

After that, he car stereo player along with its wiring connector are placed on the dashboard and are adjusted so that it completely rests within the space provided and should also be properly fit. Now the Car stereo wiring connector and the wire connector of the vehicle are to be properly linked this can be checked with the click sound produced by the connectors when they are linked.

With the help of these easy-to-do steps, remove your old fashioned cassette player and install an in-dash CD player. - 21392

About the Author:

Learn more about Autozubehoer. Stop by Author Name's site where you can find out all about Car stereo and what it can do for you.